Washing machine won't drain: what to check before you call
A full tub that won't drain or spin often has a cheap cause. Work through these checks from the free ones to the pump filter, and know where to stop.

A washer full of dirty water is stressful, but the cause is often something you can see and fix in a few minutes. This guide is a ladder. You start with the cheapest, fastest check (is the door latched?) and only climb to the fiddlier ones (the drain hose, the pump filter) if the water is still sitting there. After each check you get the same choice: if the tub drained, stop and finish your laundry. If it didn't, go to the next step.
One limit matters before you start. Every step here comes from one manufacturer's help pages, which cover top-load and front-load machines separately. They do not describe every washer on the market. Your own model's manual takes precedence over anything written here, so keep it open while you work. Some jobs belong to a technician or a plumber, and we mark that line clearly below.
What's going on
A washer that won't drain or spin is usually being stopped on purpose, or is blocked somewhere along the water's exit path. Those two ideas explain most of the checks below. The manufacturer's guides attribute non-draining to a possible installation error and review the parts of the drain system, so the cause can sit outside the machine itself (troubleshooting guide).
On the "stopped on purpose" side, the machine has safeguards. The lid or door switch lets it run only when the lid is securely closed, so an unlatched door can halt draining or spinning. An unbalanced or overloaded drum can keep it from draining and spinning properly, and the washer may stop spinning to avoid damage (troubleshooting guide). On front loaders, a large unbalanced wash can slow the spin, lengthen cycles and leave clothes wet, and an unlevel machine can become unbalanced, with extra noise or vibration (front-load help page).
Suds are another cause. Too much detergent can create excess suds that may stop the pump from moving water and the drum from spinning. On top loaders, non-HE detergent or too much of it can slow the spin and leave very wet loads (top-load help page).
Some things look like faults but are settings. Gentle cycles use slow spins, which leave more water in the load. Delicate and Hand Wash cycles spin slower to protect fabrics. On a front loader, Low or No Spin can leave water behind, and settings are remembered, so a cycle you once ran without spin will have spin turned off next time (front-load help page). Water you can hear sloshing but cannot see in the tub is normally the fluid-filled balance ring, not a drain fault.
On the "blocked" side, the drain hose can be kinked or clogged, the household drainpipe or utility sink can be blocked, or the installation may be at fault. On some front-load models the drain pump filter can clog with dirt, lint or other items.
What you can safely check or fix
Work down this list in order. Each step costs a little more effort than the one before it. These steps come from one manufacturer's help pages, so if your manual says something different, follow your manual. Every step is a check or a simple adjustment you can make without tools or a license.
- Unplug the washer from the wall outlet, and set out towels and a shallow pan for the standing water. This safety step is standard practice before you reach behind the machine or open anything, but the manufacturer pages we used do not spell it out, so confirm it in your manual's safety section.
- Find the drain and filter instructions in your manual and keep them open. Accessibility varies: the pump filter is reachable and cleanable only on some front-load models.
- Close the lid or door firmly until it latches, since the washer runs only when it is securely closed (troubleshooting guide).
- Plug the washer back in and restart the cycle. If it drained, stop here. If not, go to the next step.
- On a front loader, select Drain & Spin, which removes extra water (front-load help page). On a top loader, choose a high-spin option. If it drained, stop here. If not, go to the next step.
- Once the cycle allows, open the lid or door and redistribute the items in the drum, or take some out. A single heavy item balances worse than several items together. If it drained, stop here. If not, go to the next step.
- On a top loader, select Rinse & Spin after you have rearranged a tightly packed load (top-load help page). If it drained, stop here. If not, go to the next step.
- Measure detergent for the next load, and use less if you suspect suds. Very soft water may call for less. If it drained, stop here. If not, go to the next step.
- On a front loader, check that the machine sits level, and adjust only as your manual describes (front-load help page). If it drained, stop here. If not, go to the next step.
- Unplug the washer again before you reach behind it. Keep it unplugged for every step that follows.
- Look at the drain hose and straighten any kink (troubleshooting guide). If it drained, stop here. If not, go to the next step.
- Clear a blockage you can reach by hand in the hose or utility sink. Leave anything deeper in the drainpipe to a pro. If it drained, stop here. If not, go to the next step.
- Confirm the hose is not taped to the drain pipe, and remove the tape if it is (top-load help page). If it drained, stop here. If not, go to the next step.
- Check how far the hose reaches into the standpipe or laundry tub. The top-load page says no more than 5 inches (top-load help page). The front-load page says 4.5 inches (front-load help page). If it is deeper, pull it back to your manual's depth. If it drained, stop here. If not, go to the next step.
- Measure the standpipe height, as a check only. For a front loader, that page gives 39 inches minimum and 96 inches maximum. The top-load page says the hose cannot extend higher than 96 inches from the floor and gives no minimum. A separate general troubleshooting guide lists 30 inches minimum and 96 inches maximum without naming a machine type. Your manual's number for your model is the one to trust. Do not cut, raise or relocate the standpipe: changing it is drainage plumbing work. If the height is outside your manual's range, go to the pro section. Otherwise, go to the next step.
- If you have a front loader whose manual says the drain pump filter is user-accessible, confirm the washer is still unplugged and the pan and towels are in place.
- Open the filter following your manual's instructions, and let the water drain into the pan.
- Remove dirt, lint or other items from the filter, then refit it as shown in the manual (troubleshooting guide). The manufacturer says to clean it occasionally.
- Plug the washer in and run a drain cycle. If it drained, stop here. If not, go to the next section.
Where to stop and call a pro
If you have worked through the ladder and the tub is still full, the problem is probably beyond a homeowner's checks. Two different trades may be involved, depending on where the problem sits.
Stop here: If the load is balanced, the hose is clear and the filter is clean (or not user-accessible on your model) and the washer still won't drain or spin, the job is a pump, switch or wiring repair for a qualified appliance technician. Do not open electrical parts of the machine yourself.
Call a licensed plumber if the trouble is in the house plumbing: a blocked house drain, a drainpipe blockage you cannot reach by hand, or a standpipe whose height is outside your manual's range. The manufacturer's guide itself attributes some non-draining to possible installation error, and changing a standpipe or drain line is plumbing work, not a laundry-room adjustment (troubleshooting guide).
Call an appliance technician when the house drain is clear and the washer itself still will not pump or spin. Your state's licensing rules vary, so use the site's Find a Pro search for your state and the trade you need, and check the license lookup linked on each listing.
What to tell the pro
A clear description saves a technician time. Before you call, write down:
- The symptom: water stays in the tub, or the drum will not spin, or both. Mention whether clothes come out very wet.
- Machine type: top-load or front-load, since the checks differ.
- Any error code on the display, copied exactly as shown.
- The cycle and settings you used, including whether spin was off or set low.
- Load size and detergent: how full the drum was, and how much and what kind of detergent you used.
- Checks already done: door or lid latched, load redistributed, machine level, hose straightened and clear, hose depth in the standpipe, standpipe height measured against your manual, and whether you cleaned the drain pump filter.
- Noises: any grinding or vibration. Water sloshing that you can hear but not see is normally the balance ring.
Having the list ready shows the technician or plumber which causes you have already ruled out.
Quick answers
What is the cheapest thing to check first when my washer won't drain?
Make sure the lid or door is fully closed and latched, because the washer will only run when it is securely closed. After that, check the cycle setting, since slow-spin cycles leave more water in the load.
Can too much detergent stop a washer from draining?
Yes. Excess detergent makes suds that may stop the washer from pumping water and spinning. Measure detergent each time, and very soft water may need less.
Can I clean the drain pump filter myself?
On some front-load models the filter is accessible and can be cleaned, and the manufacturer says to do so occasionally. Check your manual first, and call a technician if your model does not provide user access.