What to reset when your thermostat is wrong after the clock change
After daylight saving time, a thermostat can run on the wrong schedule or go blank. Here is what you can safely reset yourself and where an HVAC pro takes over.

The clocks changed, and now the house is cold when you wake up, the heat runs while nobody is home, or the thermostat screen is dark and you cannot tell whether anything is working. That is uncomfortable, and it is easy to assume the furnace has failed.
Often it has not. A thermostat that follows a schedule only helps if its clock is right, and a blank screen most often points to lost power at the thermostat itself. This guide covers the part a homeowner or renter can do without a license: checking the time and schedule, swapping batteries, and restarting the system the way a manufacturer describes. It also marks the point where the job moves into wiring and equipment that belong to a licensed HVAC pro. Your thermostat's own manual always wins over a general guide.
What's going on
A programmable thermostat adjusts temperatures automatically from a set schedule, according to the Department of Energy. It saves money and energy by changing the temperature at set times of day, such as when people are at work. The schedule only works if the thermostat's clock agrees with real time. If the clock is an hour off after the change, every setting shifts with it, so the heat arrives early or late.
Smart thermostats work a little differently. The same Department of Energy page says they can adjust to occupancy or activity, can be controlled from a smartphone, and can track energy use. If yours is connected, part of its clock and schedule may live in an app, so the wrong time may show up there as well as on the wall.
A blank screen is a separate problem. A manufacturer's help page says a blank, unresponsive screen likely means the thermostat lost power, commonly from dead batteries or a tripped breaker. Another manufacturer's support page says an unresponsive keypad or screen could be locked, could need a power cycle, or could have a real problem. The clock change did not necessarily cause the blank screen. It is just the time of year many people look at the thermostat and notice.
One more case can look like a dead screen but is not. A thermostat without a C-wire, a wire that supplies steady AC power, draws its power from the HVAC system, and its screen sleeps to conserve energy, according to a third manufacturer's page. That page says a sleeping screen does not affect operation and settings can be changed from the app.
What you can safely check or fix
Work from the simplest cause to the less simple one, and stop when the problem is solved. Everything here happens at the thermostat, in its app, or at the furnace's own power switch. None of it involves opening equipment, touching wires or working at the breaker panel.
- Turn the HVAC system off at the thermostat's system setting, so nothing tries to run while you work.
- Read the time and day on the display.
- If either is wrong, correct it using the clock instructions in your thermostat's manual, since the buttons differ by model.
- Open the schedule settings.
- Compare the wake, away, home and sleep times (or whatever periods your model uses) with your actual day.
- Correct any times or days that are wrong, following the manual.
- If the buttons do nothing, open the app and look for a keypad lockout. A manufacturer's support page says that while the lockout is on, changes can only be made from the app.
- Turn the lockout off in the app, then try the buttons again.
- If you have a smart thermostat, compare the time and schedule in the app with the wall unit.
- If the screen is blank, pull off the faceplate. A manufacturer's help page describes this as the way to reach the batteries.
- Fit fresh batteries of the type your manufacturer recommends.
- If the display still acts strangely, take the batteries out again. The support page says to wait until the display goes completely blank before putting them back.
- Put the batteries back in.
- Check that the furnace's own power switch is on. The help page lists this as a check after a power problem.
- Wait 60 seconds. This is the manufacturer's reboot method after power irregularities: off, wait, then on.
- Turn the HVAC system back on at the thermostat.
- Give the system at least 10 minutes to start. The help page says modern thermostats may have time delays that protect the equipment.
- Look at the air filter. The same page says a clogged filter can cause safety mechanisms to shut the system off, which mimics a thermostat failure.
- If the filter is clogged, replace it by following the furnace or air handler manufacturer's instructions.
- Look at where the thermostat sits. The help page says direct sunlight, drafts or heat sources nearby can trick its sensors.
A note on batteries: one support page says to replace them when the indicator shows two bars or less. Another says that if the screen does not wake as you walk up, its battery needs replacing. If your screen sleeps even with good batteries, check your manual before assuming a fault, because some models sleep on purpose to save power.
If you suspect the breaker has tripped, do not work at the panel yourself. That is a job for a pro, covered below.
Where to stop and call a pro
The reset steps above are about the thermostat's face and its power supply. The line is crossed when the cause points to wiring, the electrical panel, the equipment itself, or a system that will not run.
Stop here: Low-voltage wiring, C-wire power, breaker panel work, and any furnace or AC that will not run after the steps above are jobs for a licensed HVAC pro.
The manufacturer's help page says to stop and call a pro for frayed wiring, error codes that return after a reset, or burning smells. It also warns that working on high-voltage HVAC equipment without training can cause severe injury or damage. Do not open the furnace or air handler to look for the trouble, and do not test or rewire the thermostat's terminals.
The C-wire deserves its own mention. If the screen keeps going dark and the cause seems to be missing steady power, the fix is a wiring change, not a battery change. One manufacturer says a wire in the C terminal means the thermostat has AC power and its screen should not go blank. Checking that terminal means working on wiring, so leave it to a technician.
Other signs it is time to call:
- The screen stays blank after power is restored. The help page says to call a professional.
- An alert code you do not recognize appears. The page advises against bypassing serious system errors and says to contact a certified technician.
- The display is only partly working after you have troubleshot it. A support page suggests putting back the original or a manual thermostat to keep control of the system, then contacting the maker's support.
For licensed HVAC pros, use the state license lookup linked on this site's Find a Pro pages.
What to tell the pro
A short, accurate account saves the technician time. Have these ready:
- What you saw: wrong schedule, wrong clock, blank screen, or a partial display.
- When it started, and whether it followed the clock change or a power flicker.
- Whether the thermostat is a basic programmable model or a smart one with an app, and the model name on the faceplate.
- What you already tried: new batteries, the lockout setting, the furnace switch, the off, wait 60 seconds, on restart, and the air filter.
- Whether the system ran after you waited out the recommended delay.
- Any error or alert code on the screen, written down exactly.
- Anything that points to trouble, such as a burning smell or frayed wiring.
Do not present guesses as facts. If you did not check the C terminal, say so.
Quick answers
Why is my heat coming on at the wrong time?
A programmable thermostat follows a set schedule, so a clock that is off after the time change shifts every setting with it. Correct the clock, then review the schedule.
What do I do if my thermostat screen is blank?
A blank screen likely means the thermostat lost power, commonly from dead batteries or a tripped breaker. Replace the batteries and check the furnace's power switch; leave breaker panel work to a pro.
When should I call an HVAC pro?
Call for frayed wiring, error codes that return after a reset, burning smells, or a screen that stays blank after power is restored. Wiring and high-voltage equipment are not homeowner work.