Fix-It Review Find a Pro

Check outlets and cords before Christmas lights go near a sink

A room-by-room check of the light set, the extension cord and the outlet in your bathroom, kitchen and hallway, and the point where an electrician takes over.

By Cara Coley5 min read

You are standing in the bathroom, the kitchen or the hallway with a box of lights, and the only outlet in reach is next to a sink, a counter or a TV stand with a tangle of cords behind it. You need to know which outlet and which cord you can use tonight, and what would tell you to stop.

The newest federal guidance used in this guide comes from the Consumer Product Safety Commission (CPSC). Its December 6, 2017 release advises plugging outdoor-certified lights only into a GFCI-protected receptacle or a portable GFCI. Its December 6, 2018 release advises that extension cords be rated for their intended use and in good condition, with no cuts or fraying. Those two points are the backbone of the checks below.

What's going on

Three things decide whether a string of lights is a fair load for a room with water in it: the light set, the cord that feeds it and the outlet it plugs into. Each room puts a different strain on one of them.

Bathroom. The outlet is usually close to the sink, and the temptation is to run a long cord from somewhere else to reach a mirror or shelf. CPSC's advice about GFCI protection is written for outdoor-certified lights, and the sources used here state no separate rule for indoor rooms, so this guide does not invent one. What it does say: read the label on the set first, and if the set is marked for outdoor use, give it GFCI protection even on a bathroom wall.

Kitchen. Cords are already crowded at the counter. Each extension cord has to be rated for the use you have in mind and be in good condition, which is the point of CPSC's December 2009 release as well. A cord that already serves an appliance is a cord you should look at, not assume.

Hallway and TV stand. Cords here run behind furniture, where wear and cuts are easy to miss. Pull the stand out and look along the whole length.

That same December 2009 release said defective holiday lights, unattended candles and dried-out trees most often figure in decorating fires and injuries. So the light set itself gets a look in every room. One more rule applies everywhere: CPSC warned against electric lights on a metallic tree, because faulty lights can charge the tree and cause electrocution.

What you can safely check or fix

Everything here happens at the plug. None of it opens a wall, an outlet box or a panel. Work through the list once per room, with the lights off the whole time. The room notes tell you where each step matters most.

  1. Unplug the light set and any extension cord before you handle them.
  2. Read the label on the light set to see whether it is marked for indoor use, outdoor use or both (bathroom and kitchen: do this before anything else).
  3. Look on the label for the mark of a nationally recognized testing laboratory. CPSC advises lights tested by one, and its December 2008 release named UL and ETL/ITSNA as examples.
  4. Inspect each socket on the set for cracks.
  5. Inspect the wire along the set for fraying, bare spots and loose connections. CPSC advises this check for every set, new or old.
  6. Throw out any set with damage instead of repairing it.
  7. Read the rating printed on each extension cord (kitchen: check the cord you would otherwise borrow from an appliance).
  8. Run your eyes along the full length of each cord for cuts or fraying (hallway: pull the TV stand out and follow the cord to the wall).
  9. Throw out any cord with cuts or fraying and replace it with one rated for the use.
  10. Plug an outdoor-certified set only into a GFCI-protected receptacle or a portable GFCI.
  11. Keep electric lights off any metallic tree.
  12. Turn the lights off when you go to bed or leave the house, since CPSC says lights can short out and start a fire.

One gap to be plain about: GFCI outlets generally have test and reset controls, but the CPSC pages used here give no button-by-button procedure, and this guide will not make one up. Use the instructions that came with your outlet, or the manufacturer's own help page, to test and reset it. If you cannot find them, that is a reason to ask a licensed electrician rather than guess.

If a set trips the outlet, flickers, feels hot or smells odd, unplug it and leave it off. That is a failed check, not something to work around.

Where to stop and call a pro

The checks above end at the plug. Anything behind the cover plate, inside the wall or at the panel is licensed work, in every room.

Stop here: Call a licensed electrician for a new circuit, any work inside an electrical panel, or replacing a wired outlet, including swapping a standard outlet for a GFCI one by a sink.

Call one too if an outlet is warm, discolored, loose in the wall or dead, or if a GFCI will not hold after you have followed its own instructions. Do not add cords or power strips to make up for a missing outlet near water. Each one adds another place for a cut or fray to hide, and the extension cord advice from CPSC assumes cords in good condition.

The site's Find a Pro search lists electricians with their state license number linked to the state's own license lookup.

What to tell the pro

A short, specific description saves a visit. Have these ready:

  • Which room and which outlet, for example the bathroom outlet beside the sink or the hallway outlet behind the TV stand.
  • What the outlet is doing: dead, tripping, warm, loose or crackling.
  • What was plugged into it, and whether an extension cord or power strip was involved.
  • When it started, and whether it follows one light set or happens with all of them.
  • What you already checked: the light set label, damage to sockets and wires, the cord's rating and condition.
  • Whether you tried the GFCI's test and reset using the outlet's own instructions, and what happened.

Tell them plainly that you did not open the outlet or touch the panel, and keep the lights unplugged until the outlet has been looked at.

Quick answers

Can I plug outdoor-certified lights into any outlet?

CPSC advises plugging outdoor-certified lights only into a GFCI-protected receptacle or a portable GFCI. Its December 6, 2017 release is where that advice appears.

What should I check on an extension cord first?

Check that it is rated for its intended use and in good condition. CPSC says not to use cords with cuts or fraying.

Should I swap a standard outlet for a GFCI myself?

No. Replacing a wired outlet is a job for a licensed electrician, along with new circuits and any panel work.

Sources

  1. Put Safety at the Top of Your List When Decorating this Holiday Season! | CPSC.gov
  2. CPSC Releases “Do’s and Don’ts” of Holiday Decorating | CPSC.gov
  3. Ten Tips to Keep Your Holiday Home Fire and Injury Free:Fires Lead the List of Hazards Related to Holiday Decorating | CPSC.gov
  4. CPSC and NIST Team Up to Demonstrate Holiday Decorating Hazards | CPSC.gov
  5. CPSC Warns: Avoid Hazards Related to Holiday Decorating | CPSC.gov

Get the next DIY guide by email.

One trade at a time, with where to stop and call a pro. Unsubscribe any time.