Fix-It Review Find a Pro

Check Christmas lights and cords when an outlet is dead or a breaker trips

Inspect light strings, extension cords and outlet protection yourself, and learn which dead outlets, warm cords and tripping breakers need a licensed electrician.

By Cara Coley6 min read

Someone handling a string of colorful lights while stringing it onto a fir Christmas tree indoors
Photo: Eden, Janine and Jim, CC BY 2.0, via Wikimedia Commons

A cracked socket, a bare wire or a frayed extension cord can short out, overheat and start a fire, and a Christmas tree usually has several of them running for weeks at a time. On a metallic tree, a faulty set can also charge the branches and shock whoever touches one. If you are setting up this year and an outlet has gone dead, a plug feels warm or a breaker keeps tripping, the first question is whether the trouble is in the decorations or in the building.

Everything up to the plug is yours to inspect, and anything damaged is yours to replace. Everything behind the outlet cover, including the panel, belongs to a licensed electrician. Below you will find what to check, where that line sits, and what to say when you call.

What's going on

Light sets and cords spend most of the year coiled in a box. Then they get bent, tugged and plugged in all at once, which is when a damaged part shows itself. The federal product safety agency, CPSC, wants every set examined, whether new or from last year's box, for cracked or broken sockets, wire that is bare or frayed, and connections that wobble. Its holiday decorating advice says to throw out any set with those faults.

The danger is heat. A damaged set can short out, and a short can ignite a fire. That is why CPSC advises switching holiday lights off at bedtime and whenever nobody is home, as its dos and don'ts explain. In a 2008 release, CPSC also steered shoppers toward newer sets with thicker wiring and safety fuses, which are meant to keep the wires from overheating. An old, thin-wired string deserves extra suspicion.

Extension cords carry the same risk. A cord needs to be rated for the job you give it and be in sound condition, and one with cuts or fraying should stay out of use.

Shock is the other concern. Faulty lights can electrify a metallic tree, and a person touching a branch could be electrocuted. Outdoors, CPSC wants lights certified for outside use, plugged only into a receptacle with GFCI protection or into a portable GFCI.

A dead outlet, a breaker that keeps tripping or a warm plug is a different kind of problem. It may come from the building's wiring rather than from the decorations, so those cases sit on the pro side of the line further down.

What you can safely check or fix

Nothing here opens an outlet, a panel or a wall. When something is damaged, replace it rather than repairing it. Start with the safety step.

  1. Unplug every light string, cord and decoration before you handle it.
  2. Lay one light set out where the light is good.
  3. Look at every socket for cracks or breaks.
  4. Look along the wire for bare or frayed spots.
  5. Tug gently on each connection to see whether it holds firm.
  6. Throw out any set with a cracked socket, a bare wire or a loose connection.
  7. Look on each set for a label from a nationally recognized testing laboratory.
  8. Set aside any set that has no such label, since CPSC advises using only lights that a laboratory has tested.
  9. Note the color of the holographic marking on each label.
  10. Keep any set with a green marking indoors, because a December 2012 CPSC release says green means indoor use only.
  11. Reserve sets with a red marking for outdoor hanging, because the same release says red covers both indoor and outdoor use.
  12. Confirm that any set you hang outside is certified for outdoor use.
  13. Look over each extension cord for cuts or fraying.
  14. Throw out any cord that is cut or frayed.
  15. Read the rating on each cord.
  16. Compare that rating with what you plan to plug into the cord.
  17. Plug outdoor lights into a GFCI-protected receptacle or a portable GFCI.
  18. Leave electric lights off a metallic tree.
  19. Look for a Fire Resistant label on an artificial tree.
  20. Place a live tree away from fireplaces, vents and radiators.
  21. Fill the live tree's stand with water.
  22. Switch off all the lights when you go to bed or leave the house.

A note on the artificial tree label: CPSC says it means only that the tree resists fire better than one without it. The tree can still burn, so the placement and switch-off habits above still apply.

Where to stop and call a pro

The checks above end at the plug. Anything involving the building's wiring is licensed work, and so is any problem that suggests the wiring itself may be at fault. These are Fix-It Review's lines, not steps to attempt:

  • An outlet that is dead with no obvious cause, such as a tripped GFCI that will not reset.
  • A breaker that trips again after you reset it with fewer lights plugged in.
  • A cord, plug or outlet cover that feels warm, smells hot or looks discolored.
  • Any need for a new circuit, a new outlet or work in the electrical panel. These are never homeowner jobs.
Stop here: a dead outlet, a breaker that keeps tripping, or a plug or cord that runs warm needs a licensed electrician. Unplug what is on that circuit, leave the panel alone, and do not wire in a fix.

Until the electrician arrives, keep the lights on that circuit switched off, since CPSC links shorted lights to fires.

What to tell the pro

A clear description saves time and helps the electrician decide what to bring. Write down the following before you call:

  • Which outlet or room is affected, and whether it is indoors or outdoors.
  • What was plugged in when it stopped working, including the light sets and any extension cord.
  • Whether a GFCI outlet or a breaker tripped, and whether it reset or tripped again.
  • Whether any plug, cord or cover felt warm, smelled hot or looked discolored.
  • What you have already done: which sets you threw out, which cords you replaced, and that you unplugged everything on that circuit.
  • Whether the lights carried a testing laboratory label, and which color the marking was.

To find a licensed electrician in your state, use the Find a Pro search on this site, which links each listing to the state's own license lookup.

Quick checklist before you plug in

  • Everything unplugged while you inspect.
  • Every light set checked for cracked sockets, bare wires and loose connections.
  • Damaged sets and cords thrown out, not patched.
  • A testing laboratory label on each set, with the marking matching where it will hang.
  • Extension cords rated for the use and free of cuts or fraying.
  • Outdoor lights on a GFCI-protected receptacle or a portable GFCI.
  • No electric lights on a metallic tree.
  • Artificial tree checked for a Fire Resistant label.
  • Live tree away from heat, with the stand filled with water.
  • Lights off at bedtime and when you leave the house.

Quick answers

Can I plug outdoor lights into any outlet?

No. CPSC says to use lights certified for outdoor use and connect them only through a GFCI-protected receptacle or a portable GFCI.

How do I know if a light set is safe to use?

Inspect it for cracked sockets, bare or frayed wires and loose connections, and throw out damaged sets. CPSC also advises using only lights tested by a nationally recognized testing laboratory.

Can I put lights on a metallic tree?

CPSC says no: a faulty set can charge a metallic tree, and someone touching a branch could be electrocuted.

Sources

  1. Put Safety at the Top of Your List When Decorating this Holiday Season! | CPSC.gov
  2. CPSC Releases “Do’s and Don’ts” of Holiday Decorating | CPSC.gov
  3. CPSC, NFPA and the Maryland State Fire Marshal Team Up to Prevent Holiday Decoration Fires and Injuries | CPSC.gov

Get the next DIY guide by email.

One trade at a time, with where to stop and call a pro. Unsubscribe any time.